#FlowRate
To meet surging demand for high-capacity heat exchangers, SwRI expanded its testing capabilities to address a significant market gap for equipment providing high-heat transfer rates involving high-temperature and -flowrate applications
#TechToday #DeepSeatoDeepSpace
October 27, 2026 at 7:30 PM
Same 1/4" port… phir cylinder speed different kyun? ⚙️
💬 Comment “FLOWRATE” for the sizing inputs.
zurl.co/Z2ZuS
#Pneumatics #SolenoidValve #IndustrialAutomation #Cylinder #ControlPanel #SmidMart
September 29, 2026 at 10:01 AM
dom feedee goes hard here but
dialing up the flowrate on their oxygen mask before fucking to >reduce< the risk of a pulmonary event
keeping a defib right next to their bed just in case...
choosing bedroom location based on where it'd be easiest for them to be cut out of the wall by a paramedic team
September 14, 2026 at 11:58 PM
Changing Nozzle Internal Geometry to Increase FDM Flowrate
Changing Nozzle Internal Geometry to Increase FDM Flowrate
Hackaday Article
hackaday.com
September 11, 2026 at 2:08 AM
Changing Nozzle Internal Geometry to Increase FDM Flowrate
Changing Nozzle Internal Geometry to Increase FDM Flowrate
chuckyscarnage.tech.blog
September 11, 2026 at 4:19 AM
Changing Nozzle Internal Geometry to Increase FDM Flowrate
Changing Nozzle Internal Geometry to Increase FDM Flowrate
As FDM printers keep getting faster, we are forced to deal with a range of bottlenecks, all of which conspire to hold us back from another Benchie world record. A &#8230;read more
hackaday.com
September 11, 2026 at 2:30 AM
📰 **Changing Nozzle Internal Geometry to Increase FDM Flowrate**

As FDM printers keep getting faster, we are forced to deal with a range of bottlenecks, all of which conspire to hold us back from another Benchie world record. A …read more

📰 Source […]

[Original post on igeek.gamer-geek-news.com]
September 11, 2026 at 2:02 AM
**Changing Nozzle Internal Geometry to Increase FDM Flowrate**

As FDM printers keep getting faster, we are forced to deal with a range of bottlenecks, all of which conspire to hold us back from another Benchie world record. A major physical limitation is that […]

[Original post on poliverso.org]
September 11, 2026 at 2:39 AM
If you think of it as a tap (faucet) thats running 0,10 Liters a second, its about 3,5 years of that.

A fire hydrant should have a flowrate of roughly 3750 liters a minute.

So 2 days of full spill.
September 3, 2026 at 3:44 PM
バルブとかの数値ノードから得られるFlowrateの単位ってなんだっけ
August 26, 2026 at 4:08 PM
The video in the original post shows a very slow gradual increase in pressure but this often occurs very fast, with a wave speed of 320 m/s (716 mph). Counter to the belief of many American plumbing engineers, a simple vent for the trap will not fix the issue here.
January 4, 2026 at 1:28 AM
Wintry watershed image in Ohio's Mahoning valley at Lowellville, trusty USGS river gauge (level, flowrate, parameters) foreground
February 2, 2026 at 8:52 PM
It looks like you could be a bit closer to the bed, and I would clean/wash your bed and make sure that the flowrate is dialed in by checking e-steps and than doing a flow rate test. Have you tried the teaching tech calibration steps? I also print my first layer at 50% speed for best adhesion.
August 21, 2024 at 11:48 PM
Flowrate (Arekcuta) が、配信開始されました。188円(1/23(金)3:00まで)。
store.steampowered.com/app/36...
Steamで20% OFF:Flowrate
手続き型生成の惑星群で燃料を管理する、ミニマルな宇宙サバイバルゲーム。大気をスキャンし、慎重に着陸し、動き続けろ —— 反物質が尽きれば、そこでゲームオーバーだ。
store.steampowered.com
January 16, 2026 at 3:53 AM
fission held at the lower temperature end for safety requires larger turbines to economically generate electricity; generators subsequently have more pole pairs since the turbines rotate slower the higher flowrate of steam will likely need larger condensers and more water from the cold reservoir
December 9, 2024 at 4:52 PM
Yes, the flowrate on the afarTV cam looks crazy! The fissure length is odd as it doesn't really look THAT big on video. Oh gosh, I hope poor Grindavik will be fine again.
May 29, 2024 at 3:46 PM
"Just imagine the flowrate of boba through *these* babies!"
May 16, 2026 at 9:12 PM
Bernoulli… sweeeet!
His flowrate is streamlined adorable and laminarly fluffy. ❤️
July 28, 2025 at 5:30 AM
This is the Flowrate test of the Roto Vitamins with 0.4 Revo before I do more upgrades. just about what I would expect upto 16cm² is good and it was skipping steps at 19cm². I will be upgrading to Revo Hiflow and better cooling as well as a few more milliamps.
January 3, 2025 at 9:26 PM
"Oh hey!  Can you do me a favour down there?  Can you open the valve some more and turn up the flowrate?  I want to balloon faster!"

https://www.patreon.com/posts/143580419

My Patreon Black Friday sales are on now!
Get 20% off your first month or first year.
Ends at 11:59 PM on Nov 28, 2025.
November 21, 2025 at 7:25 PM