#HYPERRAM
Sans doute. En attendant, l'Europe n'a certes rien sur les DRAM pour PC, mais Infineon (ex-Siemens) fait de bonnes RAM pour applications industrielles, soit SRAM, soit HyperRAM (une DRAM DDR 8 bits à rafraîchissement automatique, économique et assez facile à intégrer dans un circuit électronique).
October 29, 2026 at 7:08 AM
MegaST note: TOS 1.04 survives 10 extra 96 MHz wait cycles on RAM and crashes at 11, so the ST bus needs data in ~175 ns. MEGA65 HyperRAM averages ~90 ns but spikes during scaler bursts, so CPU RAM lives in SDRAM (R4-R6) or block RAM (R3). Measure the budget in sim first.

github.com/freemchr/MegaST
October 17, 2026 at 10:36 PM
it does pass the memory test, although the memory bandwidth is, at the moment, less than 2/3 of what's available with the faster revD FPGA

github.com/GlasgowEmbed...
Add HyperRAM (RAM-Pak) support to `octoram` driver by whitequark · Pull Request #1268 · GlasgowEmbedded/glasgow
Working with HyperBUS feels like having a stroke in slow motion, so I'd really rather not, but given the shortages, we may not be able to pick and choose.
github.com
September 1, 2026 at 6:21 PM
anaWire's David H. has designed an FPGA board with a twist: it's built around the Opal Kelly SYZYGY interconnect standard, to serve as a ready-to-go integration platform: the Conduit.
anaWire's Conduit Delivers a SYZYGY-Complaint Integration Platform Built on an Efinix Trion FPGA
Efinix Trion T20 board delivers 19.728 LEs, 1,044kB SRAM, 36 multipliers, with 64Mb of HyperRAM and a 28-IO SYZYGY connector on-board.
www.hackster.io
September 1, 2026 at 12:37 PM
RA8P1 Titan board features 1 GHz Cortex-M85 MCU for AIoT applications, RT-Thread development So far, if you wanted to evaluate Renesas RA8P1 Cortex-M85 MCU clocked at 1 GHz,... So far, if you wante...

Origin | Interest | Match
RA8P1 Titan board features 1 GHz Cortex-M85 MCU for AIoT applications, RT-Thread development
So far, if you wanted to evaluate Renesas RA8P1 Cortex-M85 MCU clocked at 1 GHz, you had to spend close to $200 to get the EK-RA8P1 evaluation kit, but the RT-Thread RA8P1 Titan board allows you to do that for about $50. Mostly designed for RT-Thread real-time OS development and evaluation, the RA8P1 Titan board comes with 32MB HyperRAM, 64MB HyperFlash, display and camera interfaces, two Gigabit Ethernet ports with Time Sensitive Networking support, WiFi 4 and Bluetooth 4.1, a USB 2.0 Type-C port, CAN Bus, Serial, and RS485 interfaces, a 40-pin Raspberry Pi GPIO header, a built-in debugger, and flexible power options with 5V via USB-C or 9V-24V via an XT60 connector. RA8P1 Titan board specifications: SoC – Renesas RA8P1 (R7KA8P1) MCU cores Arm Cortex-M85 clocked at 1 GHz with Helium MVE (M-Profile Vector Extension) with 32KB I/D caches; 7300+ CoreMarks Arm Cortex-M33 clocked at 250 MHz with 32KB [...] The post RA8P1 Titan board features 1 GHz Cortex-M85 MCU for AIoT applications, RT-Thread development appeared first on CNX Software - Embedded Systems News.
www.cnx-software.com
November 12, 2025 at 11:19 AM
Feed: "EE Times"
By: Sally Ward-Foxton on Tuesday, June 9, 2026
Rethinking the Logic-Routing Tradeoff in FPGAs
The Efinix Titanium Edge family of FPGAs targets edge AI, leveraging exchangeable logic cells and co-packaged HyperRAM to slash power.
www.eetimes.com
June 9, 2026 at 9:49 PM
Glasgow revD memory controller has been validated up to 125 MHz DDR! that's 2000 Mbps/chip of burst bandwidth, slightly less if you subtract overhead

Glasgow revC devices have a prototype HyperRAM addon that should not be difficult to enable, but it would have closer to 768 Mbps/chip of bandwidth
July 15, 2026 at 11:16 PM
ok so we're looking more into this with @ldcd and it seems like swapping the mode register read/write command encodings is _intentional_ to break compatibility with hyperram controllers, maybe not to pay patent fees or something?
July 3, 2026 at 9:27 AM
며칠 전에 본 소설: 계약직 신으로 살아가는 법
내가 지금 하는 것: HyperRAM 컨트롤러 신 프레임웍으로 포팅하기
머릿속 생각: 계신살 와그다스 깐프놈들은 좋겠다... 걔네는 땜질 안 해도 되고 시그널 레이턴시 그딴거 몰라도 논리만 가지고 놀 수 있잖아
October 11, 2024 at 11:24 AM
#glasgowinterfaceexplorer #rampak

Soldered everything except pin header.
September 27, 2024 at 8:01 AM
HyperRAM...
September 20, 2024 at 12:47 PM
Glasgow revD memory controller has been validated up to 125 MHz DDR! that's 2000 Mbps/chip of burst bandwidth, slightly less if you subtract overhead

Glasgow revC devices have a prototype HyperRAM addon that should not be difficult to enable, but it would have closer to 768 Mbps/chip of bandwidth
July 15, 2026 at 11:16 PM
My first time with PSoC. It's so new to me that I don't even know the part number. Th box reads PSOC™ Edge E84 AI board.

Hm, so it really is an Edge-AI thing.

Three cores there... + Quad-SPI NOR Flash and Octal-SPI HYPERRAM™
So no DDR or something fast.

Well, let's get back to work.
August 5, 2026 at 5:06 AM
Some results of the #STM32N6 img. pipeline for:
CSI + JPEG Enc. + HyperRAM.
Times for capture, to JPEG blocks and encoding (640x480):
RAM @ 100M: 41ms + 85ms + 7ms = 133ms
RAM @ 200M: 45ms (??) + 49ms + 6ms = 100ms
Code running from SRAM or XIP didn't change the results much.
July 13, 2026 at 8:34 AM
It took a LOOONG time but I figured out the issue with my bit errors on the HyperBus over 100 MHz!
Besides setting the IO voltage in registers, it is also required setting the OTP fuses! That fixed the issue and now get table 200 MHz both on HyperFlash and HyperRAM!
#stm32n6
Finally have both the HyperBus external Memories working error free at 100MHz. Was an issue with drive strengths configurations, I had to lower them on the Memory side (reflection issues?).
Stable and error free 350 MB/s reads from PSRAM (DMA).
Next figuring out limits (200MHz?)
May 26, 2026 at 10:31 AM