The solar watercress garden: how I made one
# Introduction
_The mini solar watercress garden 6 weeks after construction_
Watercress, _Nasturtium officinale_ , is a well known salad plant, one of the tastiest. It is a perennial, that grows best in chalk streams. It is best not to forage it from the wild because of the risk of liver fluke, carried in its different life-cycle phases by sheep and water snails, and giardia, a protozoan that causes severe diarrhoea. The seeds are often sold to gardeners with the note that running water is not necessary, so long as the growing medium is kept moist, for example by standing the pots in saucers of water. However, since it is adapted to running water, with its adventitious roots along the hollow, floating stems, it is worth trying to grow it in conditions that mimic its preferred habitat.
We have a small pond with a little stream, consisting of pebbles in a large broken chimney pot, fed by a submerged pump, run off mains electricity via a transformer: it is modified from a small fountain kit of the type commonly found in garden centres. I grow a little watercress there, but the shady location isn’t ideal, and we wanted more for our very diverse salads.
Having a spare 24v solar panel and a spare DC 12-24v water pump, I thought, why not make a separate water feature as a mini watercress garden.
One problem with that pairing is that the pump only runs in bright sunlight, but what if I could charge a backup battery and run the pump just for part of the daylight hours? Here then is what I built, described as a “how to”, although if making your own you can make changes and experiment around the basic idea.
# The watercress
I had sown some watercress and also “Vietnamese watercress” (from the Garden Organic Heritage Seed Library, a subscriber service available as an add-on to the general membership: it is a very valuable resource preserving many varieties that are not commercially available).
# The sump
I had a very large plastic plant pot that wasn’t being used. It had small holes in the bottom so I sealed these with some gutter and roof sealant that I had to hand, and, as belt and braces, I patched over those with a bit of roofing membrane (a cut-off had blown into the garden when the neighbours were having their roof re-built, using exterior grab adhesive. I check that it was watertight.
# The pump
The pump was purchased via ebay some years ago to make a temporary water feature. It is rated for 12v to 24v but functions perfectly well on 12 volts. It sits under the water and the outlet can be fitted with a selection of short pipe sections and fountain heads.
# Other purchases
**Solar regulator** : I used the simplest, cheapest I could find from CPC Farnell.
**12v lead acid battery** : I bought a small one from the same source as the regulator.
**Timer switch** : I found a 12v DC programmable timer switch at Low Energy Supermarket.
# The bowl
We had a terracotta, bowl-shaped planter to hand, with a diameter a bit smaller than the sump pot. The idea was to place it within the larger pot, supported on bricks, with the pump underneath it. The outlet would be routed to a small fountain head just above the bowl, which was filled with pebbles.
# Proof of concept
I initially set up the panel, regulator, battery and pump temporarily to check that the circuitry functioned.
#
#
#
#
#
#
#
#
#
#
# Control box
I then constructed a weather-proof box from scrap wood to hold the items while I waited for delivery of the timer switch (whose dimensions I knew). I had no suitable hinge so I used a strip of webbing from one of those big bags that building materials are delivered in. I made a catch from an old dungaree clip and piece of dowel. (Never throw anything away!). You could use a traditional hinge and magnetic or sprung catch. The whole control box was then wired up. I used old bike inner tube to make a weather-proof grommet where the cable from the panel would enter. I also added a switch to easily disconnect the pump. I forgot to leave enough room for the connections to the battery so it is mounted on its side. It’s a sealed unit and doesn’t seem to mind, but it isn’t ideal. It sits on a little shelf and is held in place with a piece of inner tube. Connections were all either made with screw terminals (I also had some connector blocks to hand) or via push-fit terminals, so no soldering was necessary.
|
---|---
# Mounting the panel
The panel was set in an aluminium panel. It needed some way of securing it to the garage roof where it would sit. I used 4 brass mirror plates, carefully drilling pilot holes in the aluminium and fixing them with self-tapping screws. The simplest way of mounting the panel on the slate roof of the garage was to string washing line over the roof (throwing a stick tied to a long string over first and then pulling the loop of washing line over with that) and fixing it to the board running under the guttering. Two lengths then ran over the ridge of the roof and passed through the 2 pairs of mirror plates, and anchoring them on the other side, there then being sufficient friction to hold the panel in place.
# Cabling
The panel had already been connected to the panel and the cable (on old power tool cable that I’d kept) was routed to the control box, now painted and fixed to the garage wall.
The pump came with cable and this once the sump was in place this was routed, to the control box. Mainly to deter the playful and curious foxes that visit our garden, part of it went underground through a length of conduit that, you guessed, I happened to have lying around. The cable was in two parts with a waterproof connector but the contacts were a bit corroded and impossible to clean up adequately so I got some waterproof car electrics connectors (10 in a pack, I only needed 2, for less than £5 via ebay).
**Wiring diagram waercress garden**
# Filling the sump and bowl.
Once the pump and bowl were in place, the sump was filled with enough water to very comfortably cover the pump. The pipe from the pump to the fountain-head ran through
Sump, bowl and pump in place ready for pebbles and planting.
the sole drainage hole in the bowl. Once I was happy with the geometry of it, pebbles (from B&Q) were used to fill the bowl. Limestone ones would be best as watercress prefers slightly alkaline conditions.
# Planting the watercress
The watercress had previously been transplanted into pots that could be sunk into the pebble substrate. The ordinary watercress is in a proper aquatic pot (with mesh sides) and the Vietnamese watercress is in two smaller, ordinary pots with some additional holes made in the sides.
The planted garden, two weeks after construction
# Switch-on and results
Actually, the electrics were switched on at each stage to check the worked and to check alignment and flow. It is fiddly adjusting the flow, since it means an awkward reach down to the pump in the sump, so it was good to get that right before adding pebbles and planting up.
Anyway, it all worked. The timer arrangement works well, meaning there is a regular flow of water, about 15 minutes on the hour from 9.00 till 18:15, in high summer. I’ll change the timings as the days get shorter.
The watercress seems to like the arrangement a lot, now it has matured we have plenty for a couple of pickings per week. I think the Vietnamese watercress is just a variety of the standard one. They are almost indistinguishable but the Asian one (via a West Midlands allotment, apparently) is marginally tastier.
_The completed project shortly after planting_
### Update, August 2023
July was very rainy and overcast and this meant that the battery ran down. I recharged it (with a car battery charger, it being also a lead-acid type). I also concluded that the old solar panel was insufficiently powerful in poorer light conditions for the set-up. In fact the problem was that the potential from battery and panel was insufficient to power the timer switch, despite being powerful enough to power the pump (if I bypassed the timer). I realised that the set-up would not give sufficient power year-round so did some calculations using this calculator. I then bought a small 5w panel and wired it in parallel with the existing panel. It came with a protection (or blocking) diode but the old panel didn’t have one, so I added one to it. That prevents the current flowing backwards into the weaker panel rather than to where we need it. The revised set up is now working well. After the autumn equinox I will change the timer settings so the pump runs for fewer minutes per day, allowing the battery to charge sufficiently from the lower availability of sunlight over the day.
We are now eating watercress as part of a salad twice a week and impressing our friends with the set-up too!
# Other information
Notes on watercress, cultivation and its nutritional value can be found at these links:
Plants for a Future: https://pfaf.org/plants/watercress-nasturtium-officinale/
Wikipedia: https://en.wikipedia.org/wiki/Watercress
RHS: https://www.rhsplants.co.uk/plants/_/watercress/classid.2000046807/
### Share this:
* Share on X (Opens in new window) X
* Email a link to a friend (Opens in new window) Email
* Share on LinkedIn (Opens in new window) LinkedIn
* Share on Facebook (Opens in new window) Facebook
* Print (Opens in new window) Print
*
Like Loading...
### _Related_