#StarTrekModels
November 29, 2025 at 12:06 PM
The commission I’ve been working on for the last couple of months can finally be revealed. #StarTrek #StarTrekModels #3DPrinting #ScaleModels #MKMModelwerx
October 29, 2025 at 7:38 PM
Some don’t like the #Inquiry class, but I’ve always loved it and wanted a model but there was never any in 1/1400 scale, so I bought the 1/2500 one by valkyrie013 on cults3D and scaled it up as close as I could… #StarTrek #StarTrekModels #ShipsOfStarTrek #3DPrinting #MKMModelwerx
October 28, 2025 at 2:28 PM
The 1/350 #Defiant doesn’t have most of the grid lines, so I used the 1/1000 version as a guide and pencilled in the lines before scribing them into the plastic. It’s not perfect but it’s good enough. #StarTrek #StarTrekModels #ScaleModels #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
The 1/350 #Defiant doesn’t have most of the grid lines, so I used the 1/1000 version as a guide and pencilled in the lines before scribing them into the plastic. It’s not perfect but it’s good enough....
pixelfed.social
October 14, 2025 at 9:18 PM
#Defiant’s starboard nacelle has been sanded, glued into place, LEDs wired up, closed up and lights tested. Port nacelle next. #StarTrek #StarTrekModels #ShipsOfStarTrek #ScaleModels #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
#Defiant’s starboard nacelle has been sanded, glued into place, LEDs wired up, closed up and lights tested. Port nacelle next. #StarTrek #StarTrekModels #ShipsOfStarTrek #ScaleModels #MKMModelwerx
pixelfed.social
October 10, 2025 at 6:09 PM
Had to scribe the panel lines on the #Defiant’s bridge section as there were none. Will probably have to do this with most of the model. #StarTrek #StarTrekModels #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
Had to scribe the panel lines on the #Defiant’s bridge section as there were none. Will probably have to do this with most of the model. #StarTrek #StarTrekModels #MKMModelwerx
pixelfed.social
October 7, 2025 at 7:26 AM
Taking another break from milliput/sanding on the commission build, so I’ve wired up the LEDs in its secondary hull and nacelles and completed assembly. Just need to finish… #StarTrek #StarTrekModels #ShipsOfStarTrek #ScaleModels #ModelBuilder #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
Taking another break from milliput/sanding on the commission build, so I’ve wired up the LEDs in its secondary hull and nacelles and completed assembly. Just need to finish milliput/sanding the sauce...
pixelfed.social
September 23, 2025 at 2:52 AM
Finally got round to sanding the milliput on the #Olympic. I’ve given it another coat of black to show up areas that need more milliput (and there are still a few). #StarTrek #StarTrekModels #ShipsOfStarTrek #3DPrinting #ScaleModels #ModelBuilder #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
Finally got round to sanding the milliput on the #Olympic. I’ve given it another coat of black to show up areas that need more milliput (and there are still a few). #StarTrek #StarTrekModels #ShipsOfS...
pixelfed.social
August 23, 2025 at 3:46 PM
All parts for the Type 11 shuttle has been printed. I’ve done a test fit and size comparison with the 1/1400 Galaxy Class USS Arcadia. #StarTrek #StarTrekModels #ShipsOfStarTrek #3DPrinting #ScaleModels #ModelBuilder #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
All parts for the Type 11 shuttle has been printed. I’ve done a test fit and size comparison with the 1/1400 Galaxy Class USS Arcadia. #StarTrek #StarTrekModels #ShipsOfStarTrek #3DPrinting #ScaleMode...
pixelfed.social
August 19, 2025 at 8:09 PM
Applied black primer to the #Olympic’s secondary hull and nacelles then applied milliput to the areas that needed it. #StarTrek #StarTrekModels #ShipsOfStarTrek #3DPrinting #ScaleModels #MKMModelwerx

pixelfed.social/p/mkm_modelw...
pixelfed.social
August 16, 2025 at 3:58 PM
Another #Daedalus under construction. This one is much closer to the original design than the “Essex”. 1/350 scale (roughly). #StarTrek #StarTrekModels #3DPrinting #ScaleModels #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
Another #Daedalus under construction. This one is much closer to the original design than the “Essex”. 1/350 scale (roughly). #StarTrek #StarTrekModels #3DPrinting #ScaleModels #MKMModelwerx
pixelfed.social
July 16, 2025 at 4:04 PM
LEDs wired up to the nacelles and bussard housings glued into place. Quick light test. Next up is final gap/seam filling with milliput. #StarTrek #StarTrekModels #3DPrinting #ScaleModels #ModelBuilder #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
LEDs wired up to the nacelles and bussard housings glued into place. Quick light test. Next up is final gap/seam filling with milliput. #StarTrek #StarTrekModels #3DPrinting #ScaleModels #ModelBuilder...
pixelfed.social
July 14, 2025 at 12:40 PM
Lot of progress on the 1/650 “Essex”. Just got the bussards to wire up and main assembly will be completed. #StarTrek #StarTrekModels #ScaleModels #3DPrinting #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
Lot of progress on the 1/650 “Essex”. Just got the bussards to wire up and main assembly will be completed. #StarTrek #StarTrekModels #ScaleModels #3DPrinting #MKMModelwerx
pixelfed.social
July 13, 2025 at 4:55 PM
The shipping boxes and labels arrived for the model bases. Here’s what they’ll look like. #StarTrekModels #SciFiModels #ScaleModels #ModelBuilding #ModelBuilder #MKMModelwerx
June 28, 2025 at 5:00 PM
I’ve printed my first model. 1/1400 scale Narendra (Ambassador concept) class. Model created by Dylan Wassell. You can find his work here: www.patreon.com/c/starshipsn...

#StarTrek #StarTrekModels #AmbassadorClass #NarendraClass #Federation #Starship #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
I’ve printed my first model. 1/1400 scale Narendra (Ambassador concept) class. Model created by Dylan Wassell. You can find his work here: https://www.patreon.com/c/starshipsnstuff/home #StarTrek #St...
pixelfed.social
May 30, 2025 at 2:37 PM
Milliput sanded from the gaps and seams of the Neo-Connie’s secondary hull and warp nacelles. On Thursday, I’ll paint it with black primer... #StarTrek #StarTrekModels #SciFiModels #NeoConstitution #Federation #Starship #ScaleModels #ShipsOfStarTrek #MKMModelwerx

pixelfed.social/p/mkm_modelw...
MKM Modelwerx (@mkm_modelwerx@pixelfed.social)
Milliput sanded from the gaps and seams of the Neo-Connie’s secondary hull and warp nacelles. On Thursday, I’ll paint it with black primer to see if there’s any areas I’ve missed. #StarTrek #StarTrekM...
pixelfed.social
May 20, 2025 at 8:35 PM