Want to learn hardware hacking, embedded security, and firmware reverse engineering through hands-on practice? Project Reboot by Lab401 is a deliberately vul...

Want to learn hardware hacking, embedded security, and firmware reverse engineering through hands-on practice? Project Reboot by Lab401 is a deliberately vulnerable robot that teaches you how to investigate real hardware interfaces—including UART, I²C, SPI, and Bluetooth Low Energy. 🛒 GET PROJECT REBOOT FROM LAB401 https://lab401.com/products/project-reboot-hardware-target 📖 OPEN THE COMPLETE MANUAL & WALKTHROUGH https://mindstormsecurity.com/d7f3a9b2c1e5/project_reboot_manual.html Watching tutorials can teach you the theory. Project Reboot makes you apply it. Your mission is to repair a crashed robot by completing four practical hardware-hacking challenges. Each restored system earns a heart and brings the robot back to life. The video introduces the device, demonstrates the supplied tools, explains every challenge, and shows you how to get started—without revealing the solutions. WHAT WILL YOU LEARN? 🔌 UART — Give the robot its voice back Locate its serial interface, analyze serial framing, determine the baud rate, read the boot log, access a hidden debug shell, and investigate a simulated filesystem. 📡 I²C — Restore its senses Capture a live I²C bus, identify addresses, decode communications, and recover readable information from raw bytes. 💾 SPI — Recover its memory Connect to the external flash chip, dump firmware in-circuit, extract its filesystem, and investigate the binary using real reverse-engineering tools. 📶 BLUETOOTH LOW ENERGY — Reconnect it to the world Explore BLE advertisements, understand the GATT model, connect to services, and read or write characteristics. WHAT TOOLS ARE USED? The Complete Pack contains the robot and the core equipment needed to complete its challenges: • USB-to-TTL serial adapter • CH341A flash-memory reader • SPI SOP-8 clip • 24 MHz eight-channel logic analyzer • Digital multimeter • Connection cables and accessories These are practical tools that can also be used when investigating IoT devices, embedded systems, development boards, and other electronic hardware. IS PROJECT REBOOT SUITABLE FOR BEGINNERS? Yes. The walkthrough teaches the required concepts from the ground up, so you do not need previous hardware-hacking experience. More experienced learners can skip familiar theory or switch to Hard mode for less guidance and a greater challenge. DO I NEED TO SOLDER ANYTHING? The SPI clip connects directly to the flash chip, allowing you to read it without desoldering. The challenges use accessible headers, pads, clips, probes, and wireless communication. WHICH PACK SHOULD I BUY? Choose the Basic Pack if you already own a logic analyzer, CH341A reader, USB-to-TTL adapter, multimeter, probes, and cables. Choose the Complete Pack if you are starting from zero or want a ready-to-use hardware-hacking toolkit containing everything required for the challenges. DOES IT HAVE DIFFERENT DIFFICULTY LEVELS? Yes. Every challenge has Normal and Hard modes. The online walkthrough can display the Easy/Normal material, Hard material, or both together. Progress is saved automatically, and the robot tracks completed challenges separately. WHICH OPERATING SYSTEM DO I NEED? The walkthrough covers tools for Windows, macOS, and Linux. A Linux virtual machine is recommended for a smooth security-testing environment, with Tsurugi Linux highlighted in the video as the bes option for future professional hardware hackers. WHO IS PROJECT REBOOT FOR? • Beginners who want a structured introduction to hardware hacking • Cybersecurity students and ethical hackers • IoT and embedded-security researchers • Penetration testers expanding into hardware assessments • Teachers and trainers seeking a progressive practical target • Experienced hackers looking for a compact practice platform VIDEO CHAPTERS 00:00 Introduction 00:18 What is Project Reboot? 00:28 Who is it for? 00:55 Complete Pack unboxing 01:57 Inside the robot and its ESP32-C3 02:36 Powering on and understanding the display 03:26 Manual, walkthrough, and progress tracking 04:09 Setting up your working environment 04:34 The Project Reboot mission 04:56 Who created Project Reboot? 05:22 UART challenge 05:51 I²C challenge 06:18 SPI and firmware-extraction challenge 06:51 Bluetooth Low Energy challenge 07:15 Normal mode, Hard mode, and guided learning 07:37 Real-world hardware-security skills 08:13 Basic Pack vs. Complete Pack 08:43 Why the walkthrough is worth bookmarking 08:56 Final thoughts Project Reboot is manufactured and distributed exclusively worldwide by Lab401.com

This week's pentestip is a hands-on how-to with the RFID Antenna Extender. Manufactured by Lab401, these devices are world-first: passively boost read/write/crack ranges to 7cm and displace reader zones up to 50cm. They are compatible with all 13.56MHz systems and require no wiring or soldering. We get hands-on with the devices in this week's #pentesttip!

Hi Pentesters, Welcome to #pentestips. Every Friday we will deliver a quick tip. We hope you'll enjoy those weekly tips. Also feel free to submit your tips to pentestips@lab401.com, we'll reward the best tips with discount codes, gear, etc. today's tip is about the RF-Field detector. As usual, stay safe! LAB401 team.

What the most common mistake companies make in RFID security. ICEMAN's answer. #RFID #hacking #pentesting #infosec full interview at lab401.com

The Flipper Zero is the ultimate multi-tool for pentesters, geeks, ethical hackers and hardware hobbyists alike. One pocket-sized device combines multiple tools: RFID Reading, Writing and Emulation, R...

using the RFID FIELD DETECTOR in the field, with this LAB401 tool no need to guess whether we have to work with high-frequency or low-frequency signals. visit: https://l.lab401.com/QSft7 #LAB401 #pentesting #rfid #infosec #detector

4 things kill your Flipper Zero — and most people find out the hard way. Here's how to mount the Lab401 HardShell and protect against all of them. 🔩 https://lab401.com/products/lab401-hardshell-for-flipper-zero #FlipperZero #LAB401 #HardShell #pentesting #hardwarehacking

Protect your Flipper Zero with the ultimate armor! 🛡️ Here is exactly what you get when you order the Lab401 HardShell. Inside the box: ✅ The Lab401 HardShell (3 pieces) ✅ 4x Standard replaceable GPIO boards ✅ 1x Fused replaceable GPIO board ✅ 1x set of Extra-thick silicone shoulders (to save those pins!) ✅ 1x set of silicone shoulders ✅ Screws to mount (+extra just in case) ✅ Allen key Everything you need for rugged, professional pentesting. Get yours here: https://lab401.com/products/lab401-hardshell-for-flipper-zero #FlipperZero #Lab401 #CyberSecurity #TechUnboxing #Pentesting #HackerTools

Ever wanted to make a chip "forget" its security protocols? ⚡️ In this video, we dive into EMFI (Electromagnetic Fault Injection) using the FaultyCat. By firing a precisely timed EM pulse at a microcontroller, you can potentially cause chips to glitch, leading to: ✅ Secure key leaks ✅ Protection routine bypasses ✅ Hardware vulnerability discovery Imagine having this level of hardware hacking capability in the palm of your hand. 🔗 Get the FaultyCat here: https://lab401.com/products/faultycat #HardwareHacking #Cybersecurity #EMFI #Pentesting #Lab401 #FaultyCat #Infosec #Glitching